Will this drive an LED bulb

Joined
15 Jan 2020
Messages
27
Reaction score
0
Country
United Kingdom
Hi All

Will this transformer drive a 12V LED downlight instead of a 12V Halogen ?

Would save swapping them for LED drivers

upload_2020-1-27_13-5-30.png


Thanks
 
Sponsored Links
Likely not.
The wiggly line after the 11.4V shows that the output is ac.
Not the 12V dc that you need for most LEDs.

Do you have the details of the 12V LED downlight you plan to use?

Any reason why you canot simply change to 240V downlights with 240V GU10 bulbs?
 
Likely not.
The wiggly line after the 11.4V shows that the output is ac.
Not the 12V dc that you need for most LEDs.

Do you have the details of the 12V LED downlight you plan to use?

Any reason why you canot simply change to 240V downlights with 240V GU10 bulbs?

OK thanks I get it

There is a strong preference to retain the current MR16 downlight fittings from SWMBO :)
 
Okay, note that I have never used MR16 (more used to 12V DC Led lighting).
So I am happy to be corrected.

BUT my understanding is that these following MR16 bulbs are 12V.
And being MR16's are likely to be designed to accept 12V ac.

BUT the issue is that your 'transformer' (power supply) is rated for 60W, and optimal for 20W to 60W (1VA can be considered to be =1W).
And it says on its label that it is for 'LowVoltage-Halogen Lamps'.
So it is very likely to not work properly when trying to supply LED and only 5W (some will think there is a fault and stop, some will make the LED flicker).

But you could give the following 12V a try, but likely to fail:
https://www.screwfix.com/p/lap-gu5-3-mr16-led-light-bulb-345lm-4-6w-5-pack/6557v.
https://www.screwfix.com/c/electric...e=mr16#category=cat8350001&lightbulbtype=mr16
 
Last edited:
Sponsored Links
OK thanks I get it

There is a strong preference to retain the current MR16 downlight fittings from SWMBO :)

240v GU10 lamps are also MR16 which is the size or the lamp in eighths of an inch. You could possibly change the lamp connectors and retain the fittings.

Hi All

Will this transformer drive a 12V LED downlight instead of a 12V Halogen ?

Would save swapping them for LED drivers

View attachment 182233

Thanks

No that power supply (not transformer) is not suitable for GU5.3 LEDs. This comes up regularly on these forums. That power supply gives out AC in tens of kHz, OK for halogen lights not OK for LEDs designed for DC or 50/60Hz AC.
 
240v GU10 lamps are also MR16 which is the size or the lamp in eighths of an inch. You could possibly change the lamp connectors and retain the fittings.

yeah I was wondering about that on another thread but a) it wasn't clear if I could put a 240V bulb in a 12V downlight fitting due to no earth?? and b) the 12V connector is sprung and its that that holds the bulb in place so I couldn't find a suitable replacement

upload_2020-1-27_16-7-54.png


upload_2020-1-27_16-8-59.png
 
sticking 240 lampholders in a fitting made to to operate on 12 volt is a bodge in my opinion.
Most fittings can be replaced with a similar 240 volt version , thats been tested and certified safe.
 
r if I could put a 240V bulb in a 12V downlight fitting due to no earth??
It can be done, but only if the GU10 lampholders and the attached wires are Class II, and so is the connection arrangement where the lampholder connects to the circuit wiring - typically a connector block inside a plastic box with parts to secure the flex in place.

These are Class II and can be used in some types of fitting with no earth:
gu10_class2.jpg


These are not, and are intended for Class I fittings which do have an earth connection:
gu10_class1.jpg
 

DIYnot Local

Staff member

If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.

Select the supplier or trade you require, enter your location to begin your search.


Are you a trade or supplier? You can create your listing free at DIYnot Local

 
Sponsored Links
Back
Top