Stairwell lighting went off, needing advice

[securespark]

Have worked on those Royce Thompson units before.
That one looks a bit roughly installed though...

Not sure what the white cable is doing.

 

[pete01]

Must go out to the photocell as Adrian said?

 

[pete01]

What's the point of these Royce Thompson gadgets? Just make your own with a box and a switch, No?

 

[AdrianUK]

What's the point of these Royce Thompson gadgets? Just make your own with a box and a switch, No?

Noooooooo...... there is a thermal relay inside...... kinda like the pre-empting heater in a room thermostat... its gives the photcell an in built 'delay' and hysteresis so it switches cleanly.

 

[pete01]

Noooooooo...... there is a thermal relay inside...... kinda like the pre-empting heater in a room thermostat... its gives the photcell an in built 'delay' and hysteresis so it switches cleanly.

Oooohhhh ok, I knew that

 

[SUNRAY]

It seems to be a cut-out fuse, supplying the meter - I'll bet that blew as well.

That's a standard red spot BS88 fuse holder, used to be THE fuseholder used in control panels.

I think that fuse is on the load side of the meter, but I agree that it may well be popped.

The route of live is I believe:
In from cut out bottom right - meter - red spot fuse - Royce unit, teed to - T&E

So I'll assume the door entry system is on the end of that ask if it's working before checking the photo sensor?

I assume the 3 sets reds and blacks feed the three flats.

 

[endecotp]

This el meter is only for the stairs' lights and the intercom.

Does the intercom work?

 

[garnet]

Hi all,
All is very strange.
the gray cable on the top of the meter goes to intercom electronics. They work OK.
I dont see where the cables go so they can supply the lights, but I guess lights wont be supplied through the intercom electronics.

The BS88 fuse was blown. I did change it, it works now.
White cable comes from photocell outside.
Switching to test still does not turn the lights on.
I am still not sure about the copper "pipe" switch, what its' role is.

 

[Harry Bloomfield]

That's a standard red spot BS88 fuse holder, used to be THE fuseholder used in control panels.

Yes, they push in, then slide up to lock into place. Strange use for such a fuse-holder - I wonder if the meter, is a privately owned meter, tapped into one of the flat supplies, then the freeholder was supposed to reimburse the cost of the used units, back to the flat owner?

 

[garnet]

Yes, they push in, then slide up to lock into place. Strange use for such a fuse-holder - I wonder if the meter, is a privately owned meter, tapped into one of the flat supplies, then the freeholder was supposed to reimburse the cost of the used units, back to the flat owner?

I dont know if it privatelly owned, but there is a separate live cable coming from the ground to it.
So I guess it is Energy supplier's - or the council - this used to be council building.

 

[endecotp]

I dont see where the cables go so they can supply the lights

I am still not sure about the copper "pipe" switch, what its' role is.

That’s surely the lights.

Is there another fuse inside the MEM switch box?

 

[SUNRAY]

Yes, they push in, then slide up to lock into place. Strange use for such a fuse-holder -

It looks to me to be the type that just pulls out but it matters not. I would have expected to see something more like the MEM switched fuse

I wonder if the meter, is a privately owned meter, tapped into one of the flat supplies, then the freeholder was supposed to reimburse the cost of the used units, back to the flat owner?

I dont know if it privatelly owned, but there is a separate live cable coming from the ground to it.
So I guess it is Energy supplier's - or the council - this used to be council building.

I assumed below to the right is a 3 phase company fuse feeding the 3 red cables running horizontally and then down into conduits (but this is all sopposition). It appears to be an official meter with an official coded seal so I assume its a standard energy suppliers meter with a standing charge. Another picture of that area would be likely to confirm that but it's unlikely to make any difference to the lighting fault.

Hi all,
All is very strange.
the gray cable on the top of the meter goes to intercom electronics. They work OK.

So you have power

I dont see where the cables go so they can supply the lights, but I guess lights wont be supplied through the intercom electronics.

No

The BS88 fuse was blown. I did change it, it works now.

White cable comes from photocell outside.

Yes it's a standard arrangement

Switching to test still does not turn the lights on.
I am still not sure about the copper "pipe" switch, what its' role is.

I assume the 'copper pipe' is the outgoing cable (MICC - Mineral Insulated Copper Cable) which heads out to all of the lights. As endecotp says the grey MEM box is a switched fuse, check to see if thats blown too.