Search results

A few years ago i replaced my up and over garage door with a manual insulated roller door. At time time the best thing i could come up with to close the gap between the slats on the roller part of the door and the opening was to fit a brush strip. Is there a better way?

Not long, id say under 1 minute I set the amount, press the button to commence, grab a mug add a teabag and spoon, get the milk ready and the thing is starting to dispense. You can do two cups at the same time too, one for her indoors plus me! Looks like you cant really get the one i have...

With these 'One cup' ones i found that after 2ish years use they need replacing. The inside scales up and no amount of descalant seems to work, i tried to take my last one apart to clean it all but its a nightmare and ended up just buying another. I did find a different type, the Morphy...

Thanks for the info, I assume i need to buy a programmer that will connect to the Alarm PCB? I can't do it over Wintex?

Thanks fo the reply, I have often thoguht about updating the panel firmware, i am running 5.01.03 firmware, with smarcom version 03.03.00 I have an Elite64. Is it a simple process? Do you think it is worth it, i.e. are there critical updates / is my version old? I will try to contact Texecom to...

Hi, I have a number of GJA-000x sensors on my system. I have had two that have reported low battery events as tampers and as a result thrown my system into alarm. I have read on this forum that there were a number of these sensors that have this firmware bug. I have changed one of my sensors...

Use this: https://www.amazon.co.uk/gp/product/B08MBCKJPL/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1 It comes with a coupler to connect your existing fibre cable to the extended one. Unplug the green capped fibre from your Openreach box (hard tug), try it in situ with the coupler and...

The easiest way is to log into your new ISP router and set the WiFi details (ssid and password) to be the same as what your old setup was. That way the Smart Comm will re-establish the WiFi link.

On the ios app i added a new site using the code from the alarm panel i generated, it did not add a new site like i thought it would, rather it said something like 'success' and then just showed my exisiting site in the app. It all then worked ok from then on, i did a sync panel on the app just...

Finally looked at this - got it all working again by generating a new app code on the panel and entering it on the iOS app.

Hi, I hae been using the Texecom app for around 1yr, recently upgraded to the new version 2, all was working ok. Last night i added a few extra sensors to the alarm, did not change anything else. When i now try and log in via the App, i get a "panel code not found" message with a "please...

Ok, thanks for your help. Ill live without it for now, hopefully Texecom will release a fix at some point.

Still cant get it to work, even with short names...

I recently upgraded the iOS Texecom app to v2.0.20 I notice when i look in 'Rooms & Devices', under security only certain sensors report back a temperature. All the ones that do were added to the panel back when i was using the old app. Since using the new app i added some more sensors to the...

I need some tiles (or as close to as possible) that match my existing ones in my Kitchen. I have looked at various places and cant seem to find the exact tiles. The tiles have been down perhaps 15 years or so, it may be the case they are not manufactured any more. Any help would be greatly...

This is my own thread!

This is the version number of the Ricochet software, not IP. I'm having the same issue here, if i open Ricochet from Wintex it loads fine, if i try and open Ricochet Monitor 2.18.10.0 and enter the IP of my panel with port as 10001 i cant connect..

I try to connect to my panel using the monitor software but it wont connect, i am on the same subnet as the alarm, enter the alarm IP, leave the port as default (10001) but when i hit connect it says 'Unable to connect to Premier Elite XP-W!'

So it wont work for the new GJA and GHA series sensors? How can i get battery and signal strength information?

Hi, I dont see any of my zones when i access the RF devices page.. any ideas why? I am running Wintex_7_2_2_1 (latest), selecting Diagnostics button then navigating to Control Panel > RF Devices. If i select Network 1 > Ricochet XP01 Devices i see all of my wireless devices as i should, just...