Search results

Hi all, I setup a premier elite 48 some months ago, working without issues. It replaced an old system so wiring wasn't changed to sensors but was checked for continuity. Zone 4 has suddenly come back with a tamper error. I've removed the wires on the panel and checked continuity which reads...

Hi, I have an intergas hre boiler installed with an intergas horizontal telescopic offset flue kit. The outide wall where the flue is currently will be coming into a leanto. I wanted to know if the telescopic flue is adjustable in length to clear the lean-to (ie is it just pull on the outside a...

Hi All, I am looking to have a 28m block wall built in place of fences (some of which are now neatly stacked up). I'm trying to understand the block layout, number of pillars and expansion joints that various people have told me I need! So the wall will be 2m high, 28m long, and stepping...

I appreciate this may have been done to death - nearly- but I just wanted to check before I go ahead.. I have a garden fence at present which is no longer standing due to Wind. In place of the fence I will be replacing it with a wall. Now the side where the wall will be going is the boundary...

Hi All, I installed a Premier Elite for my in-laws, and have an issue with disarming as follows: users 2 and 3 have been set pins + tags user 2 sets alarm with pin: user 2 or 3 can disarm with pin user 3 sets alarm with pin, user 3 can disarm with pin, but user 2 can only disarm with tag? Any...

Hi All, Not sure which area of the forum this goes in as it covers multiple areas, but I've put it in here as the one I think fits best! I have a walkway (my own) down the side of the house - approx 1m wide, for the full length of the house. At present, my sewage runs from the side of the...

Hi All, I have an Intergas HRE installed, with a Hot Water Zone, a radiator Zone and UFH zone. Each zone has its own zone valve. The Hot water is with Hot water priority. The Radiator Zone is just pumped via the boilers in built pump. The UFH manifold has its own zone valve and pump, along...

Morning All. My Zanuzzi washing machine didnt finish its wash cycle yesterday. Tried to run just a spin cycle and that went from running (10 min remaining) to 0 in a very short time - the pump came on for approx 30 seconds, then off, and then timer finished and door unlocked. Same for all...

I have a window bay, which had just plaster board on the inside, and has a broken felt layer and tiles on the outside. I'm going to insulate the void using ridged foam (celotex or equivalent foiled), should I put in a breathable membrane in then insulation boards and foam or just straight...

Hi all, I'm trying to add a Pyronix Twin Alert to a scantronic ion160-ex. The Scantroinc has a + and - (the previous 9752 etc i fitted previously only had a connection). The headers on the Scantronic: Twin Alert Details: At the moment the + on the panel is connected to SPK on the...

Hi all, I have a window bay that has tilted outwards, above a porch. I'm thinking of taking the whole lot off, and start again? The roof is rotten, and i can see a couple of loose bricks under the support. The wood under the window also looks like some is rotten, inside is upvc'd so cant see...

I'm looking to put a second consumer unit in my loft, to feed the loft (lights, a couple of computers, network switch - nothing heavy), and the first floor (lights and sockets) of the house - No real easy way to run twin and earth within the house, and the existing wiring is black/red and well...

Hi, Any solar installers able to tell me what the process is/maybe to install panels onto a temporary roof? Maybe a semi-perm scaffolding frame or such? NOT likely to be used for FIT or selling back to Grid.

Hi All, I've been banging my head on this for over a year now, (so long my original thread says do i really want to reply to a thread that has been idle for over a year!) But i shall persist... I am trying to set up 4 or 5? groups on my Dimension 96 panel. group a1 - i want all pirs+contacts...

Hi all, I'm looking to rewire my control centre (the installer left it in a mess with wires hanging around everywhere) and figure out why my hot water is not coming on with the programmer. Setup at the moment is: Intergas boiler HRE 1 zone valve for hot water tank - 6 wire. 1 zone valve for...

Hi all, I have an intergas her 40 SB boiler, acv smart hot water tank, 7 ufh loops and 4 radiators. I have three zone valves and a white expansion tank System was installed 2 and a half years ago. I'm finding that the boiler is cutting out due to low pressure, I top it up, to 1.2 or 1.3...

Hi All, Im just after a bit of design help and ideas. I currently have a 5m by 6m garage, + a 3.5m by 6m workshop loosely attached to each other at the bottom of my garden. (Loosely as the roofs were together, but have since fallen away!). The workshop shares one wall with the garage. there is...

Morning all, I'm in the process of setting up a Galaxy Dimension 96, last two days the alarm activates, putting the user code in silences it, but when i check event log, there are no errors to indicate why it has triggered. The alarm is not armed (As far as i am aware!). Partitions/Zoning is...

Just wanted some clarification on how to identify the keypads on my Dimension 96. On Bus a, i have expander1, expander 2, touchcenter 1. on bus b, i have keypad1, touchcenter 2. Is there a way on the keypad/touchcenter to identify which keypad is which? I had tamper alarm go off on Keypad 021.

Afternoon all, My kitchen ring has over the last week been tripping inconsistantly, sometimes taking the RCD down with it, other times just the mcb for that circuit. I suspect that the outside socket which has a fused spur off the ring may be getting wet in this recent wind/water weather event...