hive active heating

  1. S

    Hive multi zone thermostat

    good morning. I’m after so information on wiring my Hives up. I’ve just bout the active heating and extra hive We have 2 thermostats to replace. In my current thermostat they only have 4 wire. L, N, E and a L when the heating is called (CH on?) I’ve put the wires to the corresponding pins...
  2. Seb Pole

    DANFOSS TP5 (3 CORE&EARTH) to HIVE

    I am currently looking at installing a HIVE Active heating control unit to replace a Danfoss TP5. I currently have a 3 core and earth cable running to the existing heating controls (battery powered unit) I have attached my existing wiring diagram and the HIVE wiring diagram. Please also see...
  3. D

    Worcester Greenstar 24i Junior and Hive 2 Heating + Hot Water Installation

    Hi all, I have a Worcester Greenstar 24i Junior combi boiler and I want to fit a Hive 2 heating and hot water thermostat. I realise that I've bought the wrong version but I'd rather make do with what I have instead of having to send it back to get the heating only version. I believe this is...
  4. R

    Hive Wiring :(

    I’ve just purchased Hive and after reading instructions am a bit dazzled as to the wiring for an old WR1 receiver and UP2 programmer. Can anyone explain how I link out either the timer/receiver? There is also a wireless room stat but I’m guessing just decommission by removing the batteries. Any...
  5. R

    Hive Installation/Advice/Guidance Needed!!

    Afternoon all After some advice and guidance. I am looking at installing a Hive Active System (was bought a hot water and central heating kit for xmas, consisting of 1 thermostat, 1 receiver and 1 hub). We live in a new build house that has two heating zones with 2 x Danfoss TP5000...
  6. C

    Hive install to replace Danfoss system with HIU

    Hi all, I'm new to this, but I'm learning fast... I would like to upgrade my current 2 zone heating system to Hive. The current system runs off a district heat network to the flats with a heating interface unit in the flat. I have two HPA2 zone valves, two RET230P room stats and a TS715...
  7. S

    Siemens thermostat to Hive Active Heating wiring help

    Hello, We just moved into a new house that has a Siemens therm installed on a Glow worm combi boiler. It works fine but I find it really complicated to programme so want to switch to a Hive as the prices are down for 'black Friday' sales. Before I install I just want to doublecheck the wiring...
  8. trickyrick

    Replacing Honeywell ST7100 with hive.

    Hi all, Purchased a hive and as i have an oil fired Benson Jetstream boiler, BG will not install. Here's what the wiring of the old back plate looked like. What it boils down to is: Wire 1 containing: (1L) - A brown live wire coming from a fused spur, currently connected to the L. (1N) - A...
  9. X

    Hive 1 wiring help needed

    Hi folks, I know there's a ton of posts already covering hive installs...but after reading them I'm not happy to continue till I'm certain I know what I'm doing. I'm comfortable wiring it to the fused spur, but not sure about the other wires because most posts seem to involve external...
  10. B

    Connecting Hive to water controls on combi

    Hi, I have a Worcester Bosch Heatslave 12/14 Oil Boiler. The unit has controls on the front that control both the water timer / advance and the heating timer / advance. I bought a Hive system and have successfully connected to the heating side of the boiler. I am not sure how I connect the...
  11. C

    Replacement of Danfoss 102 controller with Hive 2 Active Heating

    Hi Everyone, I'm sure this has probably been asked before, I've read most of the posts on the Hive system so I think I have this correct but would like confirmation. I have a Worcester Bosch Oil fired boiler, no thermostat, and a gravity fed water tank. I currently have no way of controlling...
Back
Top