nest

Hi Everyone, I have replaced my existing Myson MEP2C with a Nest 3rd Gen. Everything went well, except there seems to be no power to the existing stat where I was planning on hard wiring the new Nest thermostat. Here is the wiring setup before at the conrol where: 3 = HW on 4 = CH on Here...

Hi everyone, I'm planning to change from Nest to Hive. I've read a few posts already (this one in particular was helpful) and I'm fairly confident I've got it right in my head, but a few things I want to check if you could help. Bit of background - we moved into a house with a system boiler...

I recently installed a Google Nest doorbell along with a Surf 2 Note Door Chime and a 12V doorbell transformer from TLC, and noticed the Surf 2 Note Door Chime is very quite when rung. Yes, it is wired correctly and has the module installed inside the door bell that came with the Google Nest...

Hey folks, I just recently moved to the UK and the way heating systems work here is new to me - apologies if this is a dumb question. In my current flat, I have an immersion heater which consists of an unvented indirect cylinder (TI120P4) for both hot water and underfloor heating. This is...

I’ll try to keep this as short as possible! Basically the timer has died on my Ecotec plus 831 combi and rather than just replace it with similar I was thinking now maybe the time to go smart and get something that can help my heating system run more economically as we’re off grid so run off...

In the attached photos you can see the wiring and wiring diagram of the receiver I am looking to replace with my Nest Thermostat E Heatlink. My question is around the Common connection. As you can see I have a jumper from L to COM. Am I correct to believe that I should use L (brown wire) as...

Hi Looking for some advice....I have just purchased a Nest 3rd Gen and are looking to install myself. I have a Honeywell ST9400C programmer for heating and hot water positioned next to my oil fired Firebird Combi boiler. I also have a Honeywell room stat. I have photographed the existing...

Hi, I have a flexicom 18hx glow worm with a nest thermostat connected. The nest panel has gone dead so I cannot switch on the heat at the moment. Can anyone explain to me how I can manually start it and override the nest setup. Google are sending me a replacement nest but won't have it for a few...

I've had a quick look on the forum and have found similar but nothing I can see that's double cabled and with a fuse box. I think I've identified the black as C and grey as NO via the forum. Question is, what do I do with the wires from the boiler and fuse box. I'm assuming these do not go to...

Hi all, I have read several posts and searched the internet and believe I have now got the correct procedure to install a Nest for my Greenstar 30DCi classic boiler with an Integral Diverter Value with a DT20 timer. If I could just get a second opinion, before I proceed it would be really...

Hi I would like to change my current thermostats to google nest thermostats. This is my current thermostat and inside I don't know if it is relevant but my boiler is Logic Combi ESP i35 boiler and it is dual-zone. I found where are my motorised valves, however, I'm not sure what to do...

Good afternoon everyone. I hoping someone could shed a little light on my current thermostat wiring. 20201116_163322 by KeyGreem posted 16 Nov 2020 at 4:50 PM20201116_161153 by KeyGreem posted 16 Nov 2020 at 4:50 PM As you can see from the first picture I have Live neutral earth coming from the...

Hi. So Combi Boiler Heating type: Water Underfloor heating, Only one Zone. Nest type: Nest Thermostat E (Images For Reference) Just received the Nest Thermostat E and trying to replace it instead of the OLD Thermostat, but I am having some difficulties with connecting the underfloor heating as...

Hi All, I have got question on installation Nest Heat link to boiler. I have got Vaillant Ecotec Pro28. I currently have Honeywell thermostat and receiver (wiring) has been shown on picture attached. Should I do exactly the same as on the picture above ie: N to N L to L With yellow/ green cable...

Hi all, I've got my UH4 setup with nest thermostats for my UFH zones, the hot water is on a timer. the nest supports hot water too so I was wondering if it was possible to use zone 4's nest thermostat for the Zone And the hot water? see attached for the wiring diagram of the uh4

Hi, I wired up my Nest (3rd gen) fine in my old house a few years ago, but have just moved into a new build and the heating system is WAY more complicated than the last one! We have a boiler in the garage, hot water cylinder in a cupboard upstairs, programmer in the utility room and two zones...

Hi all A new member here! I have bought a 3rd generation nest that I want to integrate with my Worcester greenstar 30dci classic boiler. The central heating control is straight forward enough but I can't find much advice on the hot water function wiring on my particular configuration. The...

Hi all, I have just moved into house which has the original 1980's thermostat on the wall. It is very worn and old, we are decorating and would like to replace this, hopefully with a Nest unit. The boiler we have is an old Glowworm Betacom 24c, installed in the loft. It is in very good, like...

Good morning, I've had a look at a few threads featuring a horstmann H37XL however the wiring on the posts is slightly different in that our box has 2 lives, earths and neutrals. Our central heating is a 2 zone controlled by Drayton ZA5 aculators, oil fired and currently using the horstmann...

I have a Nest gen 3 Gas C/H system in a standard size semi. Up until a couple of days ago, the hot water and central heating worked fine. The schedule and app on phone triggered as should. Nothing has changed in the house whatsoever. The thermostat and the Heat-Link(receiver) are paired so I...