plasterboard

...

Hey Everyone, So I have skimmed plasterboard before and can do that pretty well. But I had a partition put up and that was boarded and skimmed. I have had to rip a section out this weekend as I wanted to lay some pipework into the wall. As you can see from the attached picture I just ripped...

Evening, I am stripping and recreating my bathroom as my disabled daughter needs a walk-in-shower with supports, rather than just the over-the-bath shower we have at the moment. The bathroom is VERY small, so space is everything. I have stripped back all the tiles, plaster and render back to...

So I just had a new chipboard floor glued and screwed in after adding noggins and levelling the joists. There are gaps between the edge of the chipboard and the blockwork, up to 15mm. There is a gap between the dot and dab wall and the new floor of up to 40mm high amd 30mm deep and also the void...

I have to sort out a detail which seem very tricky. I have ceiling with multifinish which stops at the stair opening and then I have the stair opening itslef which need to be wrapped up with MDF to have a strong edge whcih carry over to the above flooring. I would like to have a seamless on...

Hi all, I just wanted to check with people more experienced than I that I've not missed anything major with this job of levelling out this wall. Myself and my partner are due to complete on this house soon and in the master bedroom, there is a jut where built-in wardrobes used to be...

So we've had the hall and landing taken back to brick as the original lime plaster had blown and cracked badly in corners or was hole sounding and was coated with a Chrysotile artex skim that was damaged in places. We had a professional asbestos company do this work a few days ago, who fully...

Hi, apologies if this is the wrong section. I'm in a bit of a pickle, our shower has started leaking, a lot, and it looks like there had been a small leak for a while that soaked through the grout (or round it) and destroyed the plasterboard behind it, this in turn allowed movement which made...

Hi, I have been slowly upgrading a converted loft in my victorian semi. A couple of years ago I replaced the insulation in the rafters with PIR board. 100mm in between the rafters, 25mm underneath the rafter. 50mm gap between insulation in the rafters and batten for ventilation. At the...

Hi, I'm looking to install a heavy (about 4kg) light to replace some old ones in our living room. The original one was just mounted on the plasterboard. I'm not confident that this will support the light, so want to mount it into the beam above the plasterboard ceiling. This is however 85mm...

Have a good amount of damp proof membrane left which my builder previously used when laying down concrete. Really heavy duty stuff this: https://www.screwfix.com/p/capital-valley-plastics-ltd-damp-proof-membrane-blue-1200ga-15-x-4m/98181# I'm fixing insulated plasterboards with built in vapour...

Hi folks, Bear with me as I try to describe this as best as I can, pictures paint a thousand words though so please see those too! In a relatively new build (5yrs old, housebuilder was junk, lots of issues) and it's time to tackle the gaps appearing between the wooden 'large' skirting that...

I do seem to like making life hard for myself! What screw spacing do I need for this sheet of plasterboard: - In general? - Around the cutouts? I know I'll put thousands in if I don't ask advice first! Many thanks, Stephen

Hi, Front bedroom Artex ceiling is damaged from past leak, couple of bits where it sticks downwards and there is a crack from wall to wall, possible to repair? Or job for a plasterer? Other rooms have cracks wall to wall which I assume are between the plasterboard sheets.. is there an easy...

Hi all, I hope you are well. Just looking for anyone's opinion on these cracks. Both cracks have been here since we moved in and after filling they have recently began to open again 18 months on. The first crack is against the join in the wall and runs vertical up the wall between the join. It...

I done some dob and dab and on few occasion the cut off for the electrical box is wider than the cover plate and can see the box. What would be the best and strong way to make good around it? Thanks

In our ensuite we have a dual fuel towel rail and recently the back box cover plate came away from the wall. Upon further inspection the back box is held on as per the diagram below: A plasterboard fixing (and screw) was holding the back box in place. In addition, the end of the fixing sticks...

I know this has been asked plenty of times on here but many are about 4 years old and not good to resurrect old threads so here goes. I'm looking for advice as to the best recommended stud, wiring, and pipe finder for plasterboard walls that's currently available, any advice on anything...

I have got installed new stair and now need to get ceiling up. I have no idea from where to start with batten. I have attached photos below. Any advise would be appreciated

I am using plasterboard on an angled understairs wc ceiling. Which is typically used for a ceiling or does it make any difference? 9.5mm or 12.5 min?