salus

Good afternoon everyone. I hoping someone could shed a little light on my current thermostat wiring. 20201116_163322 by KeyGreem posted 16 Nov 2020 at 4:50 PM20201116_161153 by KeyGreem posted 16 Nov 2020 at 4:50 PM As you can see from the first picture I have Live neutral earth coming from the...

New Vaillant Ecotec pro 30 boiler installed in August, worked OK for two months then the pressure suddenly dropped. Tried to raise it but it shot right up and made a very loud constant noise that we could only stop by turning water completely off. So no heating or water at all for a few days...

I've recently moved into a new flat. I have a Timeguard NTT04 (timer, not thermostat) plugged into the mains to control our Worcester Greenstar Compact boiler. I've plugged all the timings into the Timeguard and the green light comes on when it's supposed to start the heating but the boiler...

Hello, my Salus wi-fi Gateway has finally died and it's time to replace the unreliable system with a Nest. Could anyone advise on wiring the Nest heatlink to replace the iT500 RX receiver unit please? The current wiring is as per the images attached, as follows: 1. Red cable from CH COM to CH...

Hello, I know very similar questions have been asked but they haven’t covered this version of Slaus from what I have seen. I apologise if it has. I have a Valliant ecoTEC pro28 boiler which I believe has a Salus VBC600RX wireless thermostat. The boiler is a combi boiler which delivers hot...

Hi All, I have has a new Vaillant Ecotech boiler installed as well a Salus RT520TX receiver and thermostat. Everything has been going fine but I have woken up today with no heating. I have tried to pair the receiver and thermostat by holding down the pairing button which results in one solid...

Just need to confirm that this will work before I buy... I have one cable coming out of my Baxi Platinum Combi 28 HE boiler into a Salus RT500RF receiver. I want to install Hive so is it just a case of L to L, N to N, Earth to Earth and COM to No1 on the Hive? I would imagine that I would need...

Hi, I want to change my room thermostat from Sunvic TLX9201 to Salus RT300 but want to check the wiring before I do so. There are currently four wires coming out the wall. Blue + 2x Brown connected to the thermostat and the Green/Yellow connected to the back box. Can someone help me confirm...

Evening all I have the Hive thermostat on order and should be here tomorrow. I currently have a Salus RT300RF wireless thermostat which i will be replacing. The boiler is a viessmann vitopend 100 combi The current wiring on the Salus receiver is:- COM - Grey wire and brown loop NO - Black...

Hi all, I'm yet another poor sole trying to get their heads around central heating wiring. I've currently got a Salus IT500 configured to run just central heating. Boiler is a Worcester 34CDI. Now i've added UFH to downstairs I want to be able to control 2 zones, upstairs rads and downstairs...

Hi, We have just moved into an oil powered property using the Salus device. The thermostat was absent on moving in so I ordered a new one. The new thermostat is now paired and responds to the boiler no problem but is not transmitting anything to the radiators. On opening up the reciever the...

I have a RT500RF thermostat and RT500RF(RX) receiver. All is working correctly but i think I'm getting interference from a neighbour. My receiver differs from the one in all the documentation (maybe its old?) and looks like this...

Hi Folks, I am replacing installing a Salus IT500 onto my current Gas Boiler. I'm pretty sure that my wiring is correct (but could be mistaking) When I select Manual the Boiler comes on and works using the Boiler Thermostat but when I go to Auto the light goes out and boiler shuts off. I...

Hello all I’ve just moved into a new house and I have bought a Nest smart thermostat to install. I’d like to try and install this myself with your help in order to save myself a bit of cash. There is an existing wireless Salus stat already connected to the combi boiler. See photos. Please can...

The boiler's circuit board is unlabelled, but based on the current configuration hope someone can help check my deductions/proposal... At the moment: Programmer/Timer (Sunvic Select 107XL) N/L connected to its own fused spur power supply. 1/COM is connected with a Brown/Live cable to the...

Hello, I am.hoping some one could help me in regards to my problem I have recently changed my standard honeywell thermostat with a salus rt500rf unit so that I can use it upstairs wirelessly. Now that I am not technical and also first time exp with this please excuse my stupidity. I have...

A plumber suggested I could change my wired timer/thermostat by fitting a Salus RT500BC - it replaces the round mechanical timer in the boiler's faceplate (Vokera Compact). The documentation says it takes about a minute to fit, and doesn't even have any 'wiring' as such, just small metal wire...

Now it has got around to winter I'm finally getting around to fixing the thermostat on our heating. The existing Honeywell T40 Thermostat is faulty (we're just using it like an on/off switch at the moment); as its also been installed above a radiator, and on a half landing leading into the flat...

Hi, I've got the Salus T105RF which seems like the poor relation of the RT500RF but never mind... I wonder if the programme settings are telling the thermometer when to switch on and off, or when to actually *be* at either the economy or the comfort temperature. I had programmed it thinking...

Hi. I am changing to a wireless thermostat Salus rt500rf and my boiler is the Ideal Classic RS500. I have 6 wires from previous programer (2 x black, 2 x red, 2 x earth). I have tried two wiring ways, but got same result. Trial 1- put the mains live and neutral in the "L" and "N", than a loop...