Connect Aco drain to hopper/gulley

[Nialle]

Hello,
Looking advice on a DIY install of Aco slot drain to existing drainage. I am uncertain as to what type of hopper or gulley I need to connect to the Aco drain. Hopefully the pictures below show what is existing. The Aco upstand is roughly positioned where it will be when wall is rendered and patio paved. As you can see the existing drain is placed slightly in front of it. I am thinking some form of side inlet hopper, but I can't figure out which type, as inlet positions seem to be almost level with the grate. Any advice greatly appreciated.

 

[martygturner]

Normally you would use a https://www.drainageshop.co.uk/bielbet-slot-drain/inline-outlet-to-110mm-pipe.html then connect it to a hopper plugged into the drain. with a length of flexible pipe.
eg



 

[Ivor Windybottom]

You sound like you think this is going to be simple, but it isn't. You can't connect into the gulley, unless by some miracle it has an extra inlet pipe option AND has been fitted sideways, which is very unlikely.

You need to dig, and find the pipe that the gulley connects into. Then you could tee the channel into that via a suitable trap, and probably need to add a new chamber for this new junction (if it's not just a soakaway).

If it is a soakaway then you'll need to check its capacity and whether it's suitable for the added flow - it probably isn't.

Not a simple answer as it's not a simple question!

...and why's there a DPC wrapped around the wall?

 

[martygturner]

You sound like you think this is going to be simple, but it isn't. You can't connect into the gulley, unless by some miracle it has an extra inlet pipe option AND has been fitted sideways, which is very unlikely.

You need to dig, and find the pipe that the gulley connects into. Then you could tee the channel into that via a suitable trap, and probably by adding a new chamber (if it's not just a soakaway).

If it is a soakaway then you'll need to check its capacity and whether it's suitable for the added flow - it probably isn't.

Not a simple answer as it's not a simple question!

...and why's there a DPC wrapped around the wall?

Its a slim line aco, it just gets a dribble when compared to the roof drainpipe... and you connect from the end. As its rainwater unless its hitting the foul sewer no trap is required and I guess the DPC as that is where the final finish level is.

 

[jj4091]

If you move the channel out from the wall in line with the drain and use a couple of dog legs in the down spout you could connect it as shown in the example that you can scroll down to here.

ACO HexDrain Corner Unit - Plastic Grating - Vertical Outlet

A corner unit for connecting HexDrain drains at corners.

www.waterirrigation.co.uk

 

[noseall]

Hello,
Looking advice on a DIY install of Aco slot drain to existing drainage. I am uncertain as to what type of hopper or gulley I need to connect to the Aco drain. Hopefully the pictures below show what is existing. The Aco upstand is roughly positioned where it will be when wall is rendered and patio paved. As you can see the existing drain is placed slightly in front of it. I am thinking some form of side inlet hopper, but I can't figure out which type, as inlet positions seem to be almost level with the grate. Any advice greatly appreciated. View attachment 421497View attachment 421498

Swap the gully for a back inlet gully. You should be able to buy a dedicated outlet connector for those linear drains that will be spigoted for 110mm connection. Then it's a case of buying the correct bends and fittings to get from the proprietary Aco outlet into the the drain fitting.

All of it will be push fit so you can mock it all up first before comitting with concrete etc.

 

[Ivor Windybottom]

If you move the channel out from the wall in line with the drain and use a couple of dog legs in the down spout you could connect it as shown in the example that you can scroll down to here.

ACO HexDrain Corner Unit - Plastic Grating - Vertical Outlet

A corner unit for connecting HexDrain drains at corners.

www.waterirrigation.co.uk

That is a really excellent idea. They make a version of that unit with a riser collar, for use with the slotdrain version that Nialle has bought. I recognise it as I have loads of the stuff myself. The riser lifts it to the same height as the top of the slot...

ACO Brickslot Hexdrain Access and Corner Unit with Outlet | Drainage Superstore®

ACO Brickslot Hexdrain Access and Corner Unit with Outlet from ACO. (319560). Order Helpline ☎ 01752 692 221

www.drainagesuperstore.co.uk

It's then a matter of whether there's enough drop to whatever pipe it connects into.

If it's a soakaway then you don't need a trap. For a combined sewage system you do. I'd also use one for any kind of rainwater pipe system, e.g. a neighbourhood system. You're likely to get the odd whiff from the odd dead thing in there or whatever.

That DPC doesn't belong there. It will trap water against the building more than keep it out.