Not standard fuses I can just flip?

I'm replacing the CU, even if it's a simple fix, it might not be next time, it's irritating and the current one is what 30-50 years old with a bit of rejigging?
 
I
flipping the big main switch won't reset anything on those mate, they're old-school fuse carriers with wire inside that burns through when there's a fault. you'll need to turn the main switch off first before touching anything, then pull the lighting carrier out to inspect the wire. 9 times out of 10 with lights it's just a blown bulb that popped the 5 amp fuse wire, but definitely make sure the power is isolated at the main switch before you pull it.
before the CU is changed, I'm debating changing the wire myself, just worried with something this old, it still won't safely isolate or something.
 
I

before the CU is changed, I'm debating changing the wire myself, just worried with something this old, it still won't safely isolate or something.
Turn off the main switch, pull the fuse and fit a piece of 5 amp fuse wire.

See if it now works.
 
You can certainly replace the fuse wire. You have to turn off the main switch before removing or inserting the carrier, or there will be a bit of a flash and sometimes a bang. You can turn it back on after. You MUST use one strand only of the correct rating. 5A is quite thin.

Are the light bulbs it supplied modern low energy ones? Or do you have old fashioned lamps? The spotlights were particularly prone to blow a fuse when they failed. If you reconnect it and they all work but one, that was most likely the cause.
 
As above, pull the ones with the white dot and look in the middle to see if the wire has gone.
You can get some in most hardware shops, perhaps even the local aladdins cave type shop that has all the tat in the world.

Your going to need lights while you wait for the replacement CU to be sorted out.

FYI I have a similar fusebox, it's easy to replace the wire - you just need a slotted screwdriver and fusewire.
 
It's very common for the light cluster candle bulbs (3+) to go and pop the fuse, if you have one of those then that's a very likely culprit.
 
More like 20 years, TLC were listing the OPs consumer unit as current stock in 2004 and clearance stock in 2010.

I know I had one in my house built 1980, and I renewed all the fuses for MCB's and added a second one of same design, both fed from an adaptable box with two RCDs fitted, added around 1990, the second box came from my father-in-law when he upgraded his house to a more modern consumer unit.

I know Screwfix did the MCBs likely back in 2015 but not seen the whole unit for sale well before that, only the MCBs still available.

It was very easy with 5 amp fuse wire, 1795124443152.pngsold on cards to break it while tightening the screws, I would have spare holders pre-wired, for a quick change, and putting them in with the power on could cause damage Wylex burnt contacts.jpg so all ways turn off isolator first. There was a cartridge fuse version,
1795124957375.png
but seem the remember rather expensive, around £3.50 each, so not a route I wanted to go, but there were some rules I think by HSE about fuses in the care of an ordinary person, it was felt it was too easy to use the wrong wire.
 
I once had an inspection fail (in commercial premises) reason that rewirable fuses were not suitable for unskilled users. The PES engineer gave me a good written report and kindly talked me through it.

I had a lot of fun getting cartridge fuseholders to fit the variety of switch fuses, some ironclad, some wylex, some grey MEM, and passed inspection the second time round. Had to replace some of the oldest stuff. An on-site engineer used his hydraulic press to crimp terminations onto very big main bonds for me.
 
To avoid snapping the 5A fuse wire, tighten the screw at one end (the end that pulls the wire tight) while leaving the other end loose, then loop the other end under the screw head and do that one. With practice you can learn to use your thumb to put a bit of slack onto the wire so it is almost taut when finished.
 
He said I'd have to go 2nd hand though.

Everybody who buys a non-new house and does not replace the CU is using 2nd-hand devices, just like everybody who buys a used car and does not replace the tyres is driving around on 2nd-hand ones.
 
There are no end of used MCBs kicking around to fit Wylex standard. The early ones have push buttons, the later ones (made by Siemens I think) have toggle switch. You must buy them with the backing receptacle as the old ones don't quite fit. Once you take out the backs, live parts may be exposed, so only take out one at a time. This also reduces the risk that you will jumble them.
 
I would prefer just having normal switches sorted, what a pain, I guess I need a new unit.

There are benefits apart from the convenience of switches vs rewiring fuses. RCD protection, for example. And Arc Fault if you want it.
 
in the old days of tungsten lamps, they could fail with a flash, which was ionisation of the gas in the bulb, and this could cause a fuse to rupture or a trip to open,
9 times out of 10 with lights it's just a blown bulb that popped the 5 amp fuse wire,
It's very common for the light cluster candle bulbs (3+) to go and pop the fuse,

Interesting.

I remember, pre-LED, that B6s being tripped by an incandescent bulb blowing was quite common - never imagined they could take out a 5A rewireable...
 

If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.

Select the supplier or trade you require, enter your location to begin your search.


Are you a trade or supplier? You can create your listing free at DIYnot Local

 
Back
Top