tamper

Hi i have just updated my Flex 100 firmware and have reprogramed the rf zones and hopefully everything else. But its thrown up an "aux tamp 004" error. Any ideas on how to remedy it. Thanks in advance, Jeramy

Hi, I have seen some good articles on here so hopefully you can help me. I have just wired a new PIR to my Texecom Premier Elite 24 panel. The PIR I am wiring is a 'Premier Elite MR'. I copied the same wiring as my existing three PIRs but I am getting a Tamper error. I have seen some...

I have an Optima Compact G3. It was in the house already when we moved in back in 2006. It has worked fine, had to replace the battery about 10 years ago and it worked fine afterwards. A couple of months ago the tamper light came on and then none of the buttons on the keypad work. I...

After some advice gents. My alarm panel keeps triggering for tamper on the sounder. It's been fine for years. I went up recently and replaced the battery (as this also recently began to warn). Battery warn for sounder is gone but tamper remains. I tried checking the pcb and housing was...

Hi, had a look inside G4 Accenta/Optima panel and found all the blue tamper wires twisted together in one terminal and all the whites twisted together in the other? I thought they are meant to be wired in series. Has the builder Balfour Beatty wired it wrong? Also is the tamper circuit supposed...

Hi, I have a few ricochet motion and window sensors and have noticed when the battery is a low it causes a tamper alert. The Wintex software shows the battery is fine with a green bar but the tamper bar is orange. I am pretty sure the issue is low battery as it resets as soon as a new battery is...

Hi can anyone help, had our front door replaced, door contact was pulled off which triggered a tamper. Tapped in code to cancel the sounding alarm. The door contact was fitted back to the new door as it was, however we are left with a yellow warning flashing on the panel and can’t get rid of...

Hello, Been using these forums as a guest for quite a while and really appreciate all the advice. I have a Texecom Premier Elite System (64-w) installed and triggered a tamper alert from the Smartcom unit as I opened the cover whilst rerouting the ethernet cable and not being logged in in...

I have an issue with a tamper alarm on my wireless external sounder. Yesterday in the middle of the day the alarm went off on the keypad whilst alarm not set. After silencing it it told me I had a tamper alarm on the external sounder. After resetting it happened again at about 9pm. I checked...

Hi All, currently trying to build a shed base/ paved area at rear of garden. Total area for the slabs is 5.4 sq m. I have dug down 11cm and started to now fill this with about 5cm coverage sub base which I made myself out of gravel ; bits of concrete and dry soil. However I have not got a hand...

Just wondering if anyone else has experienced same issue. I fitted a premier elite wireless system just over 3 years ago. After about a year I had a battery fault on the internal sounder. Took the 8 lithium batteries out and tested them 7 were at 1.7v or above, one was 0.1v. Now after...

After a power cut today my Scantronic 9427 panel 'Tamper' light is on. How can I clear it and make the alarm usable again? I have attempted to implement the factory reset process described on page 10 of the closest I can find to my panel, which is available on line here...

Hi. I have installed a few intruder alarms over the years and I have just been asked to install one for someone at a new-build bungalow, which is ground-floor only. I now have a decision to make. I can either install the bell box at ceiling height, under the eaves, at the front of the property...

Evening all, I got home today to discover a tamper fault on my Texecom. I tried doing the latching walk test and it came up with a '......B......' on the LCD display. Not really sure what this means from the manual but anyway I progressed and opened up the panel. Below is the inside of the...

We have a accenta /optima alarm. The tamper kept going off. We have removed the wires for the bell box tamper and put a loop in. The alarm seems to be functioning ok but the leds on the bell box are not flashing. So from the outside looks like its not working. Queation is...can i leave the t...

Hi, We have a Honyewell Accenta G4 system setup in our house with control panel, 6 x PIR and 3 x door contacts. A few months ago we were having occasional issues of two of the PIRs setting off the alarm with a tamper fault. I checked ALL of the wiring on both the PIR ends and the Control Panel...

Need some help please. A PIR in my dining room broke so i decided it to remove it from the system rather than replace it. Followed instructions, from programming to devices to zones and delete. I've cleared all the logs but am still getting 2 error messages, 1. Tamper Alarm, 2 supervision loss...

Hey Everyone, I've just replaced my old accenta 6 panel alarm with the a new G4 panel and everything seems to have gone well, keypads working..etc However I just wanted to do a walk test and upon going into the menu, it keeps beeping away and showing all 1's on the display. It doesn't give me a...