Advice re installing ESI Single Channel Multi Purpose Programmer

Joined
16 Sep 2006
Messages
8,386
Reaction score
2,829
Location
Fife
Country
United Kingdom
The existing programmer is faulty and requires to be replaced. Model ESI 1 24/7. Controls electric heating only, not the hot water. See image below for the setup. Now discontinued I think, from what I can determine the direct replacement is as per the link below.

How straightforward a job to replace old for new? My electrical skills extend to wiring plugs, replacing light sockets, power sockets. What you can't see is behind the wall is a cupboard and on the wall is trunking with the cables to these items.

heating control.jpg



 
You say electric, so then big question is how much power goes through the thermostat? I would look at electric UFH thermostats, as most of them rated 16 amps, but it may be relayed anyway, so don't know what switch is required.
 
Lots have a universal/industry standard backplate, but Esi might need a wire moving, unless you go like for like?
 
Lots have a universal/industry standard backplate, but Esi might need a wire moving, unless you go like for like?
I think the existing is discontinued, the one I linked to is the up to date model. Whether it's the same internally for wiring I don't know.

Obviously could get an electrician to do it but thought if easy enough would do it myself.
 
Need to know a lot more to advise.

My basic idea is to heat as and when required, electric heating has one massive problem, electric is not a single price through the day.

So we have two options, storage, or every room independent, or a combination of both.

I tried using an oil filled radiator, I thought it would be better than using oil for central heating, but the clock change means no longer use it, as battery will not last until 00:30 when using it.

We are seeing centralised heat stores a lot more now 1793665850890.png like the old storage radiator they have a load of iron which is heated up, but it does not leak out as fast as the old radiators, but we also have water heat stores, and the pros and cons can be debated until the cows come home, but as far as this thread goes, it means the thermostat only turns on a fan, not an element.

So how your electric heating works, makes a big difference to how it is controlled.
 
Last edited:
Need to know a lot more to advise.

My basic idea is to heat as and when required, electric heating has one massive problem, electric is not a single price through the day.

So we have two options, storage, or every room independent, or a combination of both.

I tried using an oil filled radiator, I thought it would be better than using oil for central heating, but the clock change means no longer use it, as battery will not last until 00:30 when using it.

We are seeing centralised heat stores a lot more now View attachment 425724 like the old storage radiator they have a load of iron which is heated up, but it does not leak out as fast as the old radiators, but we also have water heat stores, and the pros and cons can be debated until the cows come home, but as far as this thread goes, it means the thermostat only turns on a fan, not an element.

So how your electric heating works, makes a big difference to how it is controlled.
Not saying this to be an ar5ehole but I'm not quite getting this post.

The existing programmer is faulty. As far as I'm aware it's now discontinued. Is it not as straightforward as replacing it with the up to date equivalent?

The whole setup (rads, programmer) was installed by the local council a decade or so back. Place is privately owned so they won't look at it. I think they're ceramic core rads. Mum simply turns the heating on/off at the programmer and sets each rads on-board thermostat control as desired. There's also the main thermostat on the wall beside the programmer, it obviously has ultimate control over the heating i.e. when it clicks on/off all rads do likewise.

Like I say I'm maybe missing something, however not clear to me how it's not just a case of swapping old programmer with new equivalent?
 
It is the current rating of the thermostat which is the stumbling block. A standard central heating thermostat is good for around 3 amp. Most under floor heating thermostats are rated around 16 amps, but many electric heating systems have some sort of relay so the thermostat does not switch the full 16 amp (3.5 kW) only a few milliamp, but we have not idea what your systems passes through the thermostat.

It seems there are a few versions, this one
1793704800298.png
Shows it can switch 16 amp resistive or 4 amp inductive, so is likely OK, the wiring diagram
1793704956286.png
shows no terminals for the earth wire, I assume that is some sticker found on the thermostat, which one would hope also on the old one.

But to say OK just swap it, is not really correct, as we have no knowledge of the heating device used, easy for me doing the job, I have a clamp on ammeter and can see very quickly what power goes through the device, but I can't do that remotely.
 
I think the existing is discontinued, the one I linked to is the up to date model. Whether it's the same internally for wiring I don't know.

Obviously could get an electrician to do it but thought if easy enough would do it myself.
Sorry, i missed the link to new one. If it's rated at 16A, then will be fine, but I don't think it is. No idea why @ericmark is on about a thermostat.
 
Last edited:
Sorry, i missed the link to new one. If it's rated at 16A, then will be fine, but I don't think it is. No idea why @ericmark is on about a thermostat.
I totally get the need to ensure the replacement is adequately rated etc, I think what I'm struggling with is I think/thought the new model is adequately rated.

Here's a pic of the old model tech data taken from internet (the one currently installed):

old model wiring.jpg


Here's the tech data and wiring for the new model. To me they're the same so a direct swap should be ok?

new model tech data.jpg


new model wiring.jpg
 
I totally get the need to ensure the replacement is adequately rated etc, I think what I'm struggling with is I think/thought the new model is adequately rated.

Here's a pic of the old model tech data taken from internet (the one currently installed):

View attachment 425738

Here's the tech data and wiring for the new model. To me they're the same so a direct swap should be ok?

View attachment 425739

View attachment 425740
Should be fine if the same rating, i would say go for it
 
I have to agree. I think it's a drop in replacement, and that's why they (almost) kept the same part number. I checked the archive on the wayback machine, and it was 13 years back that they referred to the unit you have, but unfortunately the crawler didn't download the installation pdf of anything that year. :(
 
Brief update on this.

New unit installed ... kind of.

Recess at rear of unit to accommodate wiring wasn't quite as deep as the old unit, meaning it's (safely) installed but slightly proud of wall. I'll need to consider buying a gang extender/pattress to give the extra depth or might cobble something together myself.

It's annoying because had the depth been ok, it would have been a direct and easy swap.
 

If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.

Select the supplier or trade you require, enter your location to begin your search.


Are you a trade or supplier? You can create your listing free at DIYnot Local

 
Back
Top