Search results

Hi, To start with, I will be getting a qualified professional to install my EV charger. However, in preparation, there are some things that I would like to understand a bit about before engaging someone to do this work. My home was fully rewired in 2019 and hasnt been touched since so is a...

Hi, I have four UFH zones, each with a wired thermostat (230V). I would like to have app control over the thermostats, but prefer to reuse the existing wired connections. Can anyone suggest a good option for replacement thermostats? Thanks and regards

Hi, I am really struggling to get some stains off my white uPVC window frames (UK). I attach a picture. This problem is on the bottom frames where the rain water runs off the window pane. I have tried a number of products - - HG uPVC cleaner - Sandtex Trade -PVC cleaner - No Nonsense...

I am hoping someone can help with some information about the apps used with start TRVs on radiators. Can you create and control zones of multiple radiators? e.g. where a room has three radiators and I want to control the room, or if I want to control one room and a hallway together. I want to...

Hi, I am wanting to replace the laminate flooring in a room, however, it looks like the flooring was laid before the skirtings and the radiator pipes are right against the skirting. There is a radiator on the other side of the room with a similar problem so can't really just slide the flooring...

Hi, I am not sure if I am posting in the right forum. I have natural gas (boiler and fire) and have the needed CO detectors installed. This got me thinking as to why we don't install gas detectors? Will CO detectors pick up leaking natural gas - I didnt think so. Can some one help with my...

Hi, I am joining some timber worktops using the normal tie rods. However, because I only need to do a couple I am not purchasing a jig. I plan to route the straight line for the bar; and then drill the wide holes at each end to hold the fasteners (the end dumbells). What diameter should...

Hi, I want to replace my normal manually operated heating control. i.e. where I actually have to go to the control to change the times the heating comes on and off. I want to be able to be able to change the on and off programmes remotely. I dont need or want thermostats or any other...

Hi, I plan to build my own general purpose work bench. The main reason is that I can have the exact size I require. The main structure will be constructed by 4" x 2" timber. My problem is how to construct the top. Initially I was planning to use the same 4x2 timber and screw five of these to...

Hi, I have painted windowsills and uPVC window frames (both white). I need to fill the gap between them (maybe up to 5mm gap). Should I use an exterior caulk such as this available form Screwfix - https://www.screwfix.com/p/no-nonsense-exterior-decorators-caulk-white-310ml/9735h This might...

Hi, As part of our renonavion, we have had floor tiles laid. These have a very light Jasmine grout and I want to do whatever I can to try and keep the grout clean (kitchen). The builder sealed the grout initially with Tilerite sealer (aerosol) application. I really dont know just how good a...

Hi, I have had all the skirtings replaced with primed MDF. After sanding there are some areas where this is back to the wood so will need primed again. There are also new timber door frames with knots that will need covered. Is there a primer that will do both - maybe Zinsser Bulls Eye 1-2-3...

Hi, Can some one advise on the best fixings to use to fit the satellite dish bracket to a brick wall. It is a zone 2 80cm dish. Should I be using masonry screws (no plug), normal screws/plugs (maybe 80mm), some sort or rawl bolt? Thanks for any help.

Hi, I am hoping this is the correct place to post this. I understand that there are two main ways to wire RJ45 sockets - 568 A or B. And that B is the more common. My electrician has wired all my sockets as 568A. These all run to my loft and are as yet ununterminated and I plan to connect...

Hi, Just about to decorate a whole house and want to use a bigger roller - 12". Does anyone supply 12" (or bigger) roller trays that have fitting liners. I can see loads for 9" but not bigger. Thanks and regards, TS

I am installing a satellite dish on the side gable wall of my house (left side looking out the front). The required direction is virtually straight toward the front (maybe a degree or two to the left (away from the house. The problem is that I have a roof step out over the wall - tile, fascia...

Hi, Historically I have seen plywood used to sheet in a shower enclosure (stud walls). I was told by my tile supplier that the building regulations now require a tile backer board for stud walls in showers. Is this correct? Just want to ensure he isn't trying it on. I guess it is a better...

Hi, I am thinking about suspended track lighting with three circuits and hence 5 wires - L1, L2, L3, N and E. And specifically how to connect the five core cable at the ceiling. Is there such a thing as a ceiling rose that will allow three live connections rather than the normal single?

Hi, Can someone recommennd or point me in the right directing for a track lighting system. In my new kitchen, I have a vaulted ceiling (peak at 14 feet) and an island with a Velux window above. So lighting isn't going to be straight forward. So I have been thinking of a suspected track...

Hi, I am after some advice. I am going through a fairly major project at the minute. I am having an attached double garage being built and this will have a concrete floor (with DPM). I want a maintenance floor covering (we park cars each night) and am planning to go for hard plastic tiles...