honeywell

Hi All, This may have been asked before, but I need some help wiring up my honeywell 2 port valve to my heatlink, after some dodgy electrician was useless. This is the current set up and, the zonal valve stays open constantly, so when the UFH is live, so are the radiators: I can see...

Security company say my keypad needs replacing (after a Tamper 0 error). They want to charge £200 to replace. I think I can buy a new keypad for £30 on Ebay. Is it a simple process of swapping the keypad on the current backplane (checking the wall tamper) or am I being too naive?!

Hi all! Our old thermostat controller isn't working anymore, so we are looking to do a DIY upgrade from the old Honeywell BDR91 to Hive. We would appreciate some advice from the experts on this forum! We have a "Vaillant EcoTech Pro 28" combi boiler, and I have attached the current BDR91...

Hello all, Now that I’ve had an unvented cylinder fitted, I’m considering having a Google Nest (3rd Generation) thermostat fitted. I’ve read a few threads on here by others who also wanted to replace a Honeywell ST6400C controller (with room thermostat, hot water cylinder thermostat and a heat...

Hi All, I just bought a Hive and want to double check the correct wiring. I have currently installed the Honeywell BDR91 (to Hive - Combi Boiler) like this: Would probably wire it as the following, but hopefully someone can confirm or correct the setup: Thank you!

Hi, I'm trying to figure out the easiest way to fit a smart thermostat. I currently have a honeywell cmt907a backplate with cm907 thermostat on top which has two wires going into it... If I've looked at it right (photo attached). A: live B: switched live Other wires available are a blue...

I hooked up GX remote and I can set unset the alarm, view logs etc from my phone. I am trying to set up push notifications but fail at the registration part on my phone. I can register without a panel account and everything seems fine but I never get any confirmation email.I can get the account...

Hello hopefully someone can give me an answer to this question. Am looking to see if the is a programming software for the flex main thing am looking for is I have wireless fobs that say they can have the buttons changed from default to user needs in the programming software but doesn’t say...

Hi, Just swapped all my thermostats to DT90E's (6 in total) and wanted to know if I should change anything in the installer menus as per my setup. The old thermostats were 3 wire (Live, Sw-Live and Neutral) and the new ones I've wired up with just 2 wire (Live and Sw-Live). I have a Nibe...

Hi, After some advice about installing a Drayton wiser hub r. I currently have a honeywell cm907 but I'm totally lost on the wiring. I've attached photos of the current wiring and the diagram provided by Drayton. Current wiring is brown/live to A, black to B & grey not connected. Thanks in advance

Hello looking for some advice I am trying to get a TCPA2B PA fob to work with me honeywell flex 50 alarm I have successfully added the fob to a user and also enabled the remote PA fob setting however when I activate the PA fob the lights flash on the fob but nothing on the alarm anything...

Hi, We have recently moved house and now the weather has gotten colder, we are using the central heating a lot more. We are finding that the Honeywell DT92E wireless thermostat is showing the room temperature as 23.5 degrees even though we have the desired room temperature as 19.5. I have...

Hi all, I have read through as many similar posts as I can in regards to my dilemma, I couldn't see anything that was similar to mine. I have a Vaillant ecotec plus 837 with a Honeywell BDR91 and CM927. The vaillant is connected by a UK mains plug as opposed to it being hardwired with a 3amp...

Hello Everybody, I just cost myself a call out trying to work out the heating system in my new house but oh well! I have an old Worcester boiler (oil fed) with a gravity fed system. So, I wanted to install a Google nest third gen and went into the Honeywell programmer expecting to see the...

Hi All, I'm trying to upgrade my existing Honeywell CM907 thermostat to a newer Honeywell Lyric T6 but can't quite figure out how to translate the wiring from one to the other. The wiring diagrams are attached - As you can see the CM907 has two wires going to it from the boiler but the T6 also...

Had a look but can’t fathom out to change language, mine is in German for some reason. there is nothing on Honeywell website. if I do factory reset, will it need re-pairing to base unit? Tia

Please could somebody verify I got this right. On keypad menu 21 display zones. For my RF zone I get Sig 10 low 08. I take sig is current signal which is "excelent" Low refers to the lowest it has ever been? Meaning 10 excelent and 0 crap?

Hello looking for some guidance and help if I may I have just started a project to try install a Honeywell galaxy flex I completely understand it’s probably over kill for a house and someone will tell me it’s not for a DIYer but am having a go never the less I have it all set up and working...

Hi. Whilst stripping wallpaper in our utility room, I think I may have damaged our ST9400C controller. The clock is currently “stuck” at 3:30 Sun, with the override on the heating on. Pressing “ok” and “minus” for 8 seconds doesn’t do anything and I can’t find a reset option. I’m planning on...

Hi Last night my keypad sounded (alarm off at the time) and it showed a fault of +RF Entrance Hall It emitted a tone a few times before I entered my code to see the fault. It did it again this morning. Cant find this fault code in the manual. I think it relates to the wireless door sensor I...