hence the lockring on a running coupler.. it pushes the coupler tight to one side of the thread if it's a loose fit..
What am I doing wrong?
- Thread starter ban-all-sheds
- Start date
Sponsored Links
- Joined
- 11 Jan 2004
- Messages
- 42,733
- Reaction score
- 2,633
- Country
Methinks Numerical Spark was referring to Ban's diagram, not to a running joint.
he could put a lockring on that too though.. 
hi bas
i served my time at the old electric board's training school and block release at tech......
the official thread technique is half forward and quarter back.....
now to whet your appetite, with 20mm conduit the three "magic measurements" for fabrication are 6mm, 16mm and 1 1/2 inches.......
i will leave you with that one
the man who taught me to bend was once the chief electrician on the QE2 and his saying was "Beware of the man with a mark on his former" i will leave you to mull that one over as well....
best wishes
alan
i served my time at the old electric board's training school and block release at tech......
the official thread technique is half forward and quarter back.....
now to whet your appetite, with 20mm conduit the three "magic measurements" for fabrication are 6mm, 16mm and 1 1/2 inches.......
i will leave you with that one
the man who taught me to bend was once the chief electrician on the QE2 and his saying was "Beware of the man with a mark on his former" i will leave you to mull that one over as well....
best wishes
alan
Sponsored Links
on friday , i am doing a "pre AM2" tutorial with a student at my local college.
in the AM2 you have to install a single piece of tube with one set and two 90 degree bends between a trunking and light with pre drilled holes and fixed saddles ......
the kid gets the secret on friday......
in the AM2 you have to install a single piece of tube with one set and two 90 degree bends between a trunking and light with pre drilled holes and fixed saddles ......
the kid gets the secret on friday......
H
holmslaw
..
Can you get depth stops to fix round conduit? I'm envisaging a sturdy metal collar with a fixing screw you tighten by hand - slip it on at the right distance from the end depending on what length of thread you want, and when the cutter can go no further....
BTW - tried that - the end of the conduit broke up.
yes, it's called the pipe vice.. once you know the right distance, put it in the vice at that point and the vice will stop it..
did you warm the conduit up a bit first? hold it between your legs for a few minutes to soften it a bit..
no idea on the magic measurements.. do it all by eye..
at a guess...
6mm would be the length to thread to put a female bush on the end of a conduit.
16mm sould be for a coupler
1 1/2 inches would be for a running coupler.
what's the fourth measurement then?
and these would only be valid for 20mm conduit as larger couplers are longer..
Ah - aint got one, and can't justify getting one. Oh well.
No, but it was a hot day, the conduit wouldn't have been cold.
- Joined
- 8 Feb 2008
- Messages
- 435
- Reaction score
- 20
- Country
You must be gentle BAS
. BTW you could use an ordinary vice and just crush the conduit in it as its only a test exercise.
hi coljack
the 6mm is what you knock off the measurement to the back of a bend so the conduit will sit in a saddle
the 16mm is a thread or half a coupling
the 1 1/2 inch is what you knock off a box ( if doing a run with flourescent light on it with 600mm centres you knock off 3 inches-two boxes.
when you cut and thread the boxes will be at 600 mm centres.
That would explain your lack of knowledge re steel conduit.
now to whet your appetite, with 20mm conduit the three "magic measurements" for fabrication are 6mm, 16mm and 1 1/2 inches.......
i will leave you with that one
There are actually four "magic measurements" (as you call them) and you've got two of them wrong!
Utter rubbish
good evening holmlaw,
have i done something to offend you?
if i was unfortunate enough to be taught by the chief electrician on the QE2 at a multi million pound purpose built school and have been successfully installing all manner of containment since september 1981 i was wondering where you would get the ammunition to have a pop at me? this is a learning environment and i would be interested in a constructive explanation of your alternative installation methods to my "rubbish".
best wishes
alan
It's just the way he is.
I have a mark on my former FWIW.
I have a mark on my former FWIW.
I don't own a former.. but the ones at the places I end up working are usually old and have about 4 different marks on the former..
so I always do a test bend and work out the differenct to the back of the former and add that on...
View media item 10602 View media item 10605 View media item 10604 View media item 10601
or use the setsquare method if measuring from the other end..
View media item 10603
so I always do a test bend and work out the differenct to the back of the former and add that on...
View media item 10602 View media item 10605 View media item 10604 View media item 10601
or use the setsquare method if measuring from the other end..
View media item 10603
DIYnot Local
Staff member
If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.
Select the supplier or trade you require, enter your location to begin your search.
Are you a trade or supplier? You can create your listing free at DIYnot Local
Sponsored Links
