alarm

Hi All I’ve downloaded both manuals (Installation & User) but I can’t find how to setup the part set zones. I’m wanting to change the entry and exit zone when on part set as at the moment when we put it on part set the alarm instantly goes off when one of the zones picks us up. I still want...

Hello there, First time poster been driven to the site by a constant alarm notification going off in our home! 10 days ago now, my family were woken by a distant (but very noticeable) alarm noise. Not like a house alarm where decibels are high, more a constant repetition Pip Pip...Pip Pip Pip...

Evening, Im moving house in the morning and planning to leave the yale smart alarm at the current property for the new owner. Im struggling to find a way to do a factory reset or something of that nature, does anyone know. I could just remove the devices, but dont know if the hub could just be...

Hi. I have installed a few intruder alarms over the years and I have just been asked to install one for someone at a new-build bungalow, which is ground-floor only. I now have a decision to make. I can either install the bell box at ceiling height, under the eaves, at the front of the property...

Hello everyone, I am looking for a DIY wireless smart home alarm with sim card autodialer (don't mind using a gsm gateway if needed). The only two reputable options that I have come across are the ERA homeguard and honeywell evohome, but can't find many reviews online. Does anyone have any...

Hi, I have an Veritas 8 alarm system that is less than a year old, when trying to set the alarm this will not set as the panel shows PIR 4 (living room) lit up. On checking it it seems that this PIR is frozen, the red led is constantly on I have made sure that there is nothing in the path that...

Hi All, Does anybody have any experience with wiring up key switch zones on a Honeywell galaxy system? I seem to be stuck with getting this to work. Instead of an actual key switch, I want to use a relay to allow remote setting/un-setting. Looking at the manual, I need to change the...

Hi All I have just purchased a bungalow which doesn't have a alarm. I have purchased a Yale SR-320 Smart Alarm. It comes with 2 PIR and 1 door sensor. I know I need to purchase more door sensors as we have 3 points of entry but would like to know the best place to add the PIR and possibly need...

I have recently had a Pyronix Enforcer alarm installed and have 2 remote keypads, one wired and one wireless. I can change the volume of the wired keypad easily enough by going into the keypad menu, but the wireless keypad has no LCD display, so presumably does not have the same settings...

Hi, I have just moved into a new property that has a Texecom Premier 24 system throughout. When I was scanning through the control panel and seeing the status of each zone, it tells me that the front door DC is "active". The front door is locked. So I decided to have a look at the door and...

I have inherited a Wien Solid State Digital alarm clock; the digital type with flip numbers. I haven't dated it yet but I'm guessing it's from the era between the late 1960s and early 1970s. The unit works fine and is a pleasure to have. It also has a very loud alarm sound which is perfect for...

I have a texecom premier 48 (older panel) I installed a while back but cannot get it to finish arming and never have managed it... It just keeps buzzing and claiming it will arm but never does, until cancelled with the user password. I can't see anything obvious in my settings that would cause...

Hi all I recently installed a texecom alarm system to my property with a smartcom box all seems to be working correctly apart from a constant green flashing light on main panel, I did reset the panel from box but everything works as it should,any ideas to why this green light is flashing would...

Hi all please help I have a texecom 24 fitted with 2400 as per manual it's connected to the same phone line as the card reader in a shop however when I connect it up it hijacks the line constantly so the card reader can't dial out to make connection please help as I'm struggling

Hello To all, Recently I bought a house . The alarm type is Eurosec ( I believe it is CP8L) The previous owner mentioned that they never used this alarm and they forgot the code. The display shows "Mains Flt" I don't know what this means, Is there anyway to make this alarm working. Please help me.

hi Had this alarm fitted and have an iOS app called ControlPlus which works with the system inside the house. The alarm has a Wi-fi connection to my router. Outside the house, the app doesn’t function. It can’t connect. Does anyone know how to configure the control unit or the app to work...

hi guys Working on a microtech 18 today replacing the webway, replaced the old webway with a new one as was faulty but I’ve ran into an issue, when exiting engineer mode it came up with module missing, I pressed the * key to remove it but now cannot for the life of me get the module back. What...

Hi, I have been installing alarms for about 8 years and very rarely I have any problems with false alarms. and when I did i was able to solve it. Recently I have installed wired Pyronix Euro46 App alarm but once a while gets false alarms on diffrent sensors. So I did decreased sesitivity...

Hi The transformer in my alarm died with a load bang yesterday and tripped the circuit breaker. I want to replace it since the alarm still functions with just the battery but I cannot find a new part specifically for it anywhere online. Can anyone recommend a suitable alternative? Thanks Dave

Hi everyone Can someone help work out what's this box! It keeps beeping all the time, it's located above front door to my apartment 35888213_1755393327872986_6679753749734359040_n by p1otrek posted 3 Jul 2018 at 1:26 PM I got Scantronic 9930 alarm fitted, is this part of the alarm? Can I open...