shower

I have now fitted the 4th replacement Shower pump, and am getting a bit pee’d off with this –so would appreciate some advice please and hope someone can guide me in the right direction please.... The shower was professionally moved in 2011 as part of a major refurb, and at that time it was...

I want to install a mixer shower ( mira atom) I need advice on the best way to tackle it see photos I dont really want to remove any tiles if possible because they are stuck onto lath and plaster I have some room under the bath as can be seen but which way to route the hot and cold (n) any...

Hi, We are considering installing two 45A shower in a single property (multible showers). I believe the incoming service fuse is 100A. The problem is, if both showers plus other devices are used it could exceed the 100A max. Would it not matter as it's unlikely both showers used at the...

Hi all. I need to replace my shower fitting shown in the images here. But cannot find a manufacturer or model anywhere! Can anyone help identify it?

Hi, Guys would like your advice and opinions please concerning my wetroom renovations. I have stripped the walls back to bare brick and removed the previous concrete screed. Sadly, the previous screen was done by someone who didn't slope it correctly allowing water to flow out of the wetroom...

Hi I recharged the air bubble in our megaflo a few weeks ago. Since then the pressure coming from our shower seems lower than normal (and temperature of water lower too). I normally let the megaflo gurgle for 30-60mins when recharging, before I get bored. But this time I let it go for a...

As an early Xmas present, our shower has decided to play up. Now runs lukewarm only so looking for guidance. The shower offers: - cold (first 60-deg turn of handle) - lukewarm (remainder of movement) Shower has been fitted approx 5 years. Hot ran from a Worcester Bosch combi. Cold appears to...

2100 wall to take 1800 bath/shower. I'm putting studs using bathroom boards at each end to bring the 2100 down to 1800ish (just over), but the stud at the taps end will cover that whole wall to lose the pipework for new sink/toilet also. The face of the tiles infringing on the plan/footprint of...

Hello, I've a failing LED bulb over the shower tray in the bathroom, with all but three or four of the LED's no longer illuminating. However looking at it, I've no idea how to remove the fixture in front of it to remove the bulb, whether by twisting or pulling, preferably without breaking it...

I'm installing a shower head elbow wall plate (for the first time). The depth of the 1/2 inch threaded socket isn't enough to clear the depth of the backer board (see attached picture) plus a further 12mm of tile and adhesive. The joint between the shower arm and the elbow would be right in the...

Hi, I've got a Triton Zante Shower - approx 15 yrs old and still going strong with no problems until recently I noticed that I get drips from the showerhead even when the power is off. The only way to stop the dripping is to isolate the water supply which is pretty inconvenient. Is this...

Hello, I hope everyone is well. I am having some issues with my Creda Digimix Shower. It works but it is not reaching the correct temperature. For example, the range is 1-9 with a L and H setting. The normal range has always been 5/6 and this produces hot water. However, recently any setting...

Hi, We have a pulsacoil a class thermal store supplying hot water to a shower with a T bar mixer. The shower is no longer providing hot water from the shower. The pipe feeding the mixer is hot the T bar has been replaced It stayed hot for a couple of days and then slowly the temperature...

I have fitted a universal shower pump too boost hot water from gravity system to a fancy kitchen faucet (min pressure 1bar). The pump is RP80SU rated 2.4bar 10m of pipework away from the faucet, cold is mains 3.5bar. I have tried initially positive feed pump, but the flow from the faucet was...

Hi Guys, Just looking for some advice on fitting new shower tray. One wall is plastered, the other tileboard on studs. The tray edges are slightly tapered towards the bottom meaning the top is slightly away from the wall. I have cut away the plaster and board to allow the tray to sit somewhat...

Trevi A2219AA Ideal Standard CLASS fixed shower head. Can anyone tell me how to remove this fixed shower head and replace it with a standard fit hose shower. I’ve not seen one of these before. It has a castellated ring as can be seen in the photo, does that need to be turned first. What tools...

Have a Triton T75 electric shower for just over 2 years and only recently been experiencing issues with the neon lit on off button on the front in that it has begun to require several attempts pressing the button in order to turn the shower off. What could be causing this issue and should it be...

A cluster of 3 led lights, it's good because the bathroom gets very little natural light. But it's zonally conflicted in plan, being sited just outside the outer edge of the bath/shower It could do with going between the the next pair of joists but this would require extending the cables...

hi I have a Creda 950DL 9.5kw shower, approximately 8 years old. About two years ago the medium element light went out and the water ran cold if I had it set to medium. For the past two years it’s only been working on one element, meaning I had to set it to high to get any hot water. Puzzlingly...

I am trying to uninstall a Coram corner-entry shower, so I can re-silicone the joints, which are leaking. Most of the assembly looks pretty straightforward, apart from the bottom outside corner (see photo). How is this kept in place? It is just siliconed in (I can't see any screws). If anyone...